View Advertiser Index
|
Posted on 11/9/2007
|
Trailer and lots of parts
Ulhaul open trailer with a 6ft tall 6ft long V nose box. Walk on diamond tread roof with railing, covered full width tire rack, shelf in the V nose and another shelf full width of trailer inside, access door in front V, full door on one side, both lockable fold down handles. Two year old winch with good battery, aluminium diamond tread wheel stops, D rings for ratchet strap hold downs. Two year old tires with a spare. Wood floor needs replaced, useable though. $2000 as is $2400 with new floor.
Chevy 377, 305 heads, cast crank rods and pistons, qulified for Beatrice spring fling this year, true claimer. Runs better than you would think - $500
chevy bowtie heads #034 LLM heads cut for 11:1 with a flat top piston, milled, angle milled, intake face trued, push rod holes enlarged, cut for 1.5" springs, teflon seals, have not been ported, done by Spanel Engines, perfect shape, bare w/seals, studs, and guide plates - $600.
Afco aluminium threaded body double adjustable shocks, 1 7", 1 9" with coil over kits. Only 15 nights on them $200 ea.
4speed muncie 1st and 3rd removed 2nd and rev lightened, fresh profesional rebuild not ran since rebuilt - $400
Chevy 9/16" stroker crank and rods, stock 2" journal crank with 6" full floating 2" billet rods - $400
chevy vortec 906 take off heads, never raced - $250
chevy vortec 906 heads, raced 10 nights, nice set, guides machined for 1.25 springs, screw in studs, guide plates, bolt them on and go - $400
9" aluminium 31 spline full spool - $75
Chevy 350 pistons #H617p silvolite 30 over 250 domes, used complete set, good shape - $50
462 double humps never raced - $150
462 double humps, ss one piece valves, 1.25" double electro polished springs 600 lift, surfaced, 3/8" studs, guide plates, low nights, would need valve job at most to run - $350
186 double humps these have accessory holes, same as above only single 600 lift springs, angle plug, small plugs (worth 15hp on dyno), need gone through - $350
chevy 6.200", 2" journal carrilo H beam rods, forced pin oiling, nice shape - $200
chevy 400 blocks all never raced standard, 2 bare $200ea, 2 short blocks $250ea
chevy 400 stock cranks, 3 - $40 ea
Speedway brake proportioning valve - $15 ea
Afco 5.5" x 9.5" front springs, 1200(x2), 1300 - $20 ea
Afco 5" x 13" rear springs, 200, 225, 250 - $20ea
Eibach 5.5" x 9.5" front springs, 1300(x2), 1350 - $20ea
Chevy stock flex plates 163 tooth 7 350's - $5 ea, 400 chevy 163 tooth aftermarket $15, 1 flywheel 163 tooth #973456-n $10
1 welded (pin hole)champ pan, bent on back corner - $40
2 4" offset chrome beadlocks 5x5 silver sticker, ok shape -$30ea
Nitrogen bottle with smith regulator, complete setup for airing tires up, bottle is near full - $250
chevy quarter master 7.25" V drive single disc clutch, used very good shape - $300 with brand new disc $350
350 cfm Dorton carb, used 1 season. This is the better one, perfect shape. - $300
price break on multiple items, may trade for the right parts, 50cc dart or pro 180 runner heads, 7.25" triple disc clutch.
Contact Information:
Eric Rempel
Phone: (402)780-5017
Email: [email protected]
|
|
|
|
