View Advertiser Index
|
Posted on 11/9/2007
|
lots of parts and open trailer
Ulhaul open trailer with a 6ft tall 6ft long V nose box. Walk on diamond tread roof with railing, covered full width tire rack, shelf in the V nose and another shelf full width of trailer inside, access door in front V, full door on one side, both lockable fold down handles. Two year old winch with good battery, aluminium diamond tread wheel stops, D rings for ratchet strap hold downs. Two year old tires with a spare. Wood floor needs replaced, useable though. $2000 as is $2400 with new floor.
Chevy 377, 305 heads, cast crank rods and pistons, qulified for Beatrice spring fling this year, true claimer. Runs better than you would think - $500
chevy bowtie heads #034 LLM heads cut for 11:1 with a flat top piston, milled, angle milled, intake face trued, push rod holes enlarged, cut for 1.5" springs, teflon seals, have not been ported, done by Spanel Engines, perfect shape, bare w/seals, studs, and guide plates - $600.
Afco aluminium threaded body double adjustable shocks, 1 7", 1 9" with coil over kits. Only 15 nights on them $200 ea.
4speed muncie 1st and 3rd removed 2nd and rev lightened, fresh profesional rebuild not ran since rebuilt - $450
Chevy 9/16" stroker crank and rods, stock 2" journal crank with 6" full floating 2" billet rods - $400
chevy vortec 906 take off heads, never raced - $300
9" aluminium 31 spline full spool - $75
Chevy 350 pistons #H617p silvolite 30 over 250 domes, used complete set - $75
462 double humps never raced - $150
462 double humps, ss one piece valves, 1.25" double electro polished springs 600 lift, surfaced, 3/8" studs, guide plates, low nights, would need valve job at most to run - $350
186 double humps these have accessory holes, same as above only single 600 lift springs, angle plug (worth 15hp on dyno), need gone through - $350
chevy 6.200", 2" journal carrilo H beam rods, forced pin oiling, nice shape - $250
chevy 400 blocks all never raced standard, 2 bare $200ea, 2 short blocks $250ea
chevy 400 stock cranks, 3 - $50 ea
Afco adjustable biscuit J bar #20225 - $50
9" double sided J bar mount - $10
Speedway brake proportioning valves (x2) - $15 ea
Afco 9" bearing sliders, 1 five nights 1 brand new - $100 for the set or 50/60
Afco 5.5" x 9.5" front springs, 1200(x2), 1300 - $20 ea
Afco 5" x 16" rear springs, 250, 150 - $20 ea
Afco 5" x 13" rear springs, 200, 225, 250 - $20ea
Eibach 5.5" x 9.5" front springs, 1300(x2), 1350 - $20ea
Chevy stock flex plates 163 tooth 7 350's - $5 ea, 400 chevy 163 tooth aftermarket $15, 1 flywheel 163 tooth #973456-n $10
chevy small block oil pans 6qt kick out used, (3) $20 ea, 1 welded (pin hole)champ pan, bent on back corner - $40
Aero white sticker 5x5 3" offset new never used, chrome - $60
Basset white sticker 5x5 3" offset used great shape silver - $40
2 4" offset shrome beadlocks 5x5 silver sticker, ok shape -$40ea
Wheels are all 15x8, would trade for 15x8 5x5 2" offset chrome or silver white sticker or the same in 4" beadlock, need to be in decent shape.
Nitrogen bottle with smith regulator, complete setup for airing tires up - $250
chevy quarter master 7.25" V drive single disc clutch, used - $300 with brand new disc $350
350 cfm Dorton carb, used 1 season. This is the better one, perfect shape. - $300
price break on multiple items, may trade for the right parts, 50cc dart or pro 180 runner heads, 7.25" triple disc clutch.
Contact Information:
Eric Rempel
Phone: (402)416-0420
Email: [email protected]
|
|
|
|
