View Advertiser Index
|
Posted on 11/9/2007
|
Trailer and parts
Ulhaul open trailer with a 6ft tall 6ft long V nose box. Walk on diamond tread roof with railing, covered full width tire rack, shelf in the V nose and another shelf full width of trailer inside, access door in front V, full door on one side, both lockable fold down handles. Two year old winch with good battery, aluminium diamond tread wheel stops, D rings for ratchet strap hold downs. Two year old tires with a spare. Wood floor needs replaced, useable though. $2000 as is $2400 with new floor.
Chevy 377, 305 heads, cast crank rods and pistons, qulified for Beatrice spring fling this year, true claimer. Runs better than you would think - $500
Chevy 383, double hump heads (5 nights on the heads since fresh), silvolite pistons, cast crank, stock rod, balanced, #8 cam. This motor has a bunch of stock car wins on it (10 including at JMS and a 2nd at the fall IMCA race at JMS a year ago). Needs freshened. $900 complete intake to pan, this is my favorite motor.
chevy small block bowtie heads #034 LLM heads cut for 11:1 with a flat top piston, milled, angle milled, intake face trued, push rod holes enlarged, cut for 1.5" springs, teflon seals, have not been ported, done by Spanel Engines, perfect shape, bare w/seals, studs, and guide plates - $600.
Afco aluminium threaded body double adjustable shocks, 1 7", 1 9" with coil over kits. Only 15 nights on them $200 ea.
4speed muncie 1st and 3rd removed 2nd and rev lightened, fresh profesional rebuild not ran since rebuilt - $450
Chevy 9/16" stroker crank and rods, stock 2" journal crank with 6" full floating 2" billet rods - $400
Chevy 350 pistons #H617p silvolite 30 over 250 domes, used complete set - $75
462 double humps never raced - $150
462 double humps, ss one piece valves, 1.25" double electro polished springs 600 lift, surfaced, 3/8" studs, guide plates, low nights, would need valve job at most to run - $350
186 double humps these have accessory holes, same as above only single 600 lift springs, angle plug (worth 15hp on dyno), need gone through - $350
chevy 6.200", 2" journal carrilo H beam rods, forced pin oiling, nice shape - $250
chevy 400 stock cranks, 2 - $30 ea
Speedway brake proportioning valve - $15
Afco 5.5" x 9.5" front springs, 1200(x2), 1300 - $20 ea
Eibach 5.5" x 9.5" front springs, 1300(x2), 1350 - $20ea
Chevy stock flex plates 163 tooth 7 350's - $5 ea, 400 chevy 163 tooth aftermarket $15
2 4" offset 15x8 chrome beadlocks 5x5 silver sticker, ok shape -$40ea
Nitrogen bottle with smith regulator, complete setup for airing tires up - $250
chevy quarter master 7.25" V drive single disc clutch, used - $300 with brand new disc $350
350 cfm Dorton carb, used 1 season. This carb is in perfect shape. - $300
350 cfm KP carb, used 1 season since complete rebuild. This carb is also in perfect shape. - $300
9" ford rear end with disc brakes, has metric mounts on it $100
Pro Tru 406 forged 2 eye brow flat top pistons with 6" Renegade I beam floating pin rods. 6 of each $150
Midwest #6 cam new in box $40
Dynagear dry cam timing belt set up for SBC $200
Brzezinski Racing Products SBC fully modified cast iron Qjet intake like new $650 - new these are $895
Contact Information:
Eric Rempel
Phone: (402)780-5017/ 402-416-0420
Email: [email protected]
|
|
|
|
